Opened the wrong way — this page has no styling and no images.
Image and stylesheet paths are resolved from the site root (/assets/…), so opening the file directly resolves them to C:\assets\… and nothing loads.
To see it properly: unzip 2_双击进后台改字_仅Windows.zip and double-click 启动后台.bat — the browser then shows the full site with styling, images and the ZH/EN switch.
(This zip is a plain static preview: opened directly it shows one page at a time, without styles, images or the language switch.)
Once uploaded it works normally: live traffic arrives over http, not by double-clicking a file.
This notice only appears when the file is opened locally; online visitors never see it.
ProductsWireless access & coverageSwitching & data centerOptical access & transportOptics & cabling
ServicesManaged NOCImplementation & deliverySpare parts & maintenanceAdvisory & architecture
SolutionsManaged network operations & NOCCampus & wireless coverageCloud-network branchesSecurity & compliance
Case studiesScale · managed operationsSpeed · bulk migrationContinuity · legacy retrofitTechnical notes
About usCompany profileCertificationsOffices & contactTechnical notes
Resources & contactTechnical notesFAQDelivery processPricingPrivacy & termsContact usOffice address
Solutions / Campus, office and retail wireless

Campus wireless: survey, capacity planning and RF tuning

Wireless quality is not decided by how many APs you buy but by survey, capacity planning and RF tuning. With the same hardware, two designs can differ by more than 2× in measured throughput.

Multi-form
Ceiling · wall-plate · outdoor · in-wall
AC1600/2600
Wireless controllers
160MHz
5 GHz channel width
256clients
Max clients per unit

Three scenarios, three designs

Mounting APs is the same act in all three, but offices, guest rooms and outdoor areas fail for completely different reasons. Applying one template everywhere is the most common cause of poor coverage.

SCENE 01

Open-plan office

The hard part: dense desks, high concurrency, and partitions or glass curtain walls that block and reflect signal. The design focus is capacity and interference control, not range.

SCENE 02

Hotel rooms / dormitories

The hard part: every room is its own small box, and a corridor AP will not get inside. An in-wall wall-plate AP is the reliable answer, and it blends into the fit-out.

SCENE 03

Outdoor and campus

The hard part: sun, rain, lightning and long backhaul runs. That means an IP67 body, surge protection and bridge or fiber backhaul.

SCENE 04

Retail and chains

The hard part: many sites, no IT staff on site, and downtime that closes the shop. Hardware must be plug-and-play, cloud-manageable, and every store visible from head office.

Four steps: capacity and cost

01

Site survey

Read the drawings, measure ceiling height, confirm wall materials and partitions, locate the power and data risers, and mark where you cannot drill. Every later number depends on this being right.

02

Capacity calculation

Count peak concurrent clients per zone, not people, add the per-client bandwidth requirement, and work back to how many APs each zone needs and the per-unit client limit. Meeting rooms and open desks are calculated separately.

03

RF and channel planning

On 2.4 GHz only the three non-overlapping channels 1, 6 and 11 are used, staggered between adjacent APs; 5 GHz starts at 160 MHz and drops to 80 MHz where interference demands it. The output is a channel map that avoids co-channel interference.

04

Acceptance

Before handover we measure signal strength and throughput across the whole area and issue heat maps plus a per-AP report. The acceptance thresholds, which spot must reach how many dBm and Mbps, are written into the contract.

"Coverage is not done when the lights come on. It is done when a heat map proves every desk has enough." — wireless delivery engineer

Product mix

The line covers four forms — ceiling, wall-plate, outdoor and bridge — with two controllers. Specifications live on the product pages; what follows is the selection logic.

AI6220
Indoor ceiling
Wi-Fi 6 dual-band
3000 Mbps · 120+ clients
AIH-6221
Indoor ceiling
2.5G uplink
3000 Mbps · 256 clients
AIH-622
In-wall plate
86-box mount
3000 Mbps · 256 clients
AO6220
Outdoor
4T4R, surge protected
IP67 · 128 clients
ScenarioRecommended modelWhy
Open office (ceiling 2.8–3.5 m)AI6220 / AIH-6221Ceiling mount with a controlled coverage radius; the 2.5G uplink suits backhaul in dense zones
Hotel rooms / dorms / cellular officesAIH-622 (wall-plate)Fits an 86 box in the wall; signal enters the room directly instead of pushing through from the corridor
Campus perimeter / car park / loading dockAO6220IP67 body, surge board and high-power FEM, built for temperature swings, rain and snow
Multi-site managementAC1600 / AC2600AC1600 fits in a distribution box and manages 64 APs; AC2600 manages 128 with 4G/5G failover
Between buildings / lifts / long-range backhaulWireless bridge range10–30 km line-of-sight backhaul with no cabling; lift shafts use a dedicated car-mounted bridge

See the full product list and specifications →

Architecture: three tiers, one thread

The standard build is three tiers: the core switch handles routing and policy, floor PoE switches provide power and access, and the APs do nothing but radio. Controllers, location engines and wireless intrusion prevention hang off the core.

Core

Core switch / gateway

Handles VLAN segmentation, inter-subnet routing, egress policy and hosts the controller out-of-band. Dual chassis is optional, depending on how much downtime the business tolerates.

Aggregation

Floor PoE switches

One cable carries both power and backhaul, removing a mains drop at every point. Uplinks run to the core over single-mode gigabit fiber.

Access

APs and clients

Fat or fit in one box: a small site runs standalone, and multi-site estates switch to fit mode for central configuration and upgrades.

Out-of-band

Controller / location / WIPS

Pushes uniform configuration, tunes RF and sets roaming policy; UWB location and wireless intrusion prevention are added as needed on the same APs.

Five common problems

SymptomReal cause and what to do
Full bars, slow networkCo-channel interference or channel planning that has failed. More APs will not fix it; redo the channel and power plan
Drops and reconnects when you walk next doorRoaming is not configured, or the APs do not share one SSID and key. Put them under a controller
Meeting rooms stall as soon as people joinPlanned by headcount instead of concurrent clients, so capacity is short. Dense rooms need extra APs
Signal will not reach the guest roomsCorridor ceiling APs trying to punch through two walls. Switch to in-wall wall-plate APs
Devices fail en masse after two yearsIndoor models used outdoors, or no surge grounding. Check the protection rating at selection time

Delivery and acceptance

We hand over more than installed hardware. Three artifacts stay with you:

DOC 01

Coverage heat maps

Signal strength and SNR per floor, with weak zones marked and the remediation already applied noted.

DOC 02

AP and channel schedule

Mounting position, orientation, channel, power and VLAN for every AP, filed at handover so later expansion follows the same plan.

DOC 03

Client experience test report

Measured throughput and roaming at representative desks, meeting rooms and corridors, with handover time and packet loss recorded.

DOC 04

Operations handover

Platform accounts, alert rules and a runbook for common issues, written so your IT team can take over directly.

Send us a floor plan and we will size the AP count first.

Request a coverage estimate →